Decision dossierEvidence reviewed
meat slicer

Hobart 2812 Parts & Repair Costs: Used-Buy Risk Guide

Hobart 2812: OEM part prices, the failure points reported in our sources, and what to inspect before you buy used.

Status: published
Recallnone found
Known risks7
Sources9
Verified2026-09-05
Buy-Risk Verdict
Inspect before buying · moderate confidence
Short answer: Reported problems: won't start (carriage not home or a bad home switch), stops mid-use, and hard slicing from a dull blade or worn bushings. Buy only after inspection.

Sources last checked on Sep 5, 2026. No verbatim quote is on file for this record yet.

Decision status
inspect

Reported problems: won't start (carriage not home or a bad home switch), stops mid-use, and hard slicing from a dull blade or worn bushings. Buy only after inspection.

Confidence 58%
Used price
Not published

We show a used price only when the dated listings behind it are linked. None are on file for this model yet.

Part prices below link to the seller page they came from.
Repair Risk Matrix

What can make the cheap machine expensive?

ComponentSeverityRepair cost (only where a source states it)
Stops running midmediumnot yet verified
Automatic mode failsmediumnot yet verified
Difficult slicingmediumnot yet verified
Poor slice qualitymediumnot yet verified

Failure points come from the technician, owner and parts sources listed under Sources. They are reports, not failure rates, and no cost is shown unless a source states it.

General Hobart slicer troubleshootingmedium

General Hobart slicer troubleshooting (Parts Town's official guide, brand…

Cost not yet verified
Won't startmedium

Won't start: carriage not in "home" position, home switch malfunction…

Cost not yet verified
Stops running midmedium

Stops running mid-use: carriage tray improperly installed or missing…

Cost not yet verified
Automatic mode failsmedium

Automatic mode fails: not set to automatic; "auto/man or auto speed…"

Cost not yet verified
Difficult slicingmedium

Difficult slicing: dull/worn blade, worn transport bushings or carriage…

Cost not yet verified
Poor slice qualitymedium

Poor slice quality: "dull slicer knife blade is the biggest culprit…"

Cost not yet verified
2812medium

2812-specific part catalog implies the knife-drive motor and the knife…

Cost not yet verified

Common questions

What fails on the Hobart 2812?

The most cited concerns in our evidence record: Stops running mid, Automatic mode fails, Difficult slicing. See the risk breakdown above for details and sources.

Key parts and observed prices

PartPart #Observed priceAs of
Knife Sharpener Assembly, Domestic Slicers00-873847-00001$539.052026-09-05
Meat Grip Kit00-913067$296.802026-09-05
Ball Bearing, Knife ShaftBB-021-66$32.742026-09-05

Prices are point-in-time observations from the linked seller pages, not quotes. Availability and pricing change.

What fails on the Hobart 2812, and the parts to know

What to test before you buy

  • Won't start: cycle the carriage to its home position and press the underside overload reset before assuming a dead motor.
  • Slices ragged or uneven: usually a dull or undersized knife; run a full sharpen cycle and re-check before condemning the blade.
  • Automatic mode quits: run it in automatic for several strokes (not just manual) to expose an auto-speed sensor fault or a dirty position-sensor vane.
  • Hard to slice or drags: worn transport bushings or a dry carriage slide rod (the rod must be lubricated).

Commonly replaced parts (OEM part numbers)

  • Poly-V drive belt: 00-438845 (the wear item on the knife drive)
  • Pulley kit: 00-937969 (supersedes obsolete sheave 00-439049)
  • Slicer knife: 00-439870-00006 or 00-439870-00005 (two blade SKUs list under the 2812; a four-figure part: confirm knife diameter and carriage type first)
  • Knife-drive motor: 00-438846-00001 (115/230V)
  • Motor start switch: 00-271612-00003 (supersedes obsolete 00-271612-00002)

Before you order a part

  • Buy by Hobart part number, not by "model 2812"; parts are shared across the 2000-series and many list under sibling models (2912B, "1000/2000").
  • A used unit's electrical parts may already sit on a superseded revision (the current start switch supersedes an obsolete one).

Part numbers and failure points are cross-referenced from the OEM-authorized Parts Town catalog (parts diagram); confirm the exact part against your unit's data/serial tag before ordering, and get a current price quote.

Sources

  1. webstaurantstore.comretailer · research-cited · accessed 2026-08-19
  2. betterdealstoday.comweb · research-cited · accessed 2026-08-19
  3. offerup.comweb · research-cited · accessed 2026-08-19
  4. partstown.comparts-retailer · research-cited · accessed 2026-08-19
  5. partstown.comparts-retailer · research-cited · accessed 2026-08-19
  6. Hobart - 2812 Slicer Operationvideo-transcript · research-cited · accessed 2026-08-19
  7. Hobart sharpening videovideo-transcript · research-cited · accessed 2026-08-19
  8. Hobart Sales & Service - How to Sharpen a slicervideo-transcript · research-cited · accessed 2026-08-19
  9. partstown.com part listings (prices observed 2026-09-05)parts-retailer · verified · accessed 2026-09-05
Spot an error? Challenge this record

Found an out-of-date code section, a wrong verdict, or a better primary source? Tell us. Corrections that check out are applied, with the change shown in history. That is our standing policy.

Read next

Guides that cover the Hobart 2812

Related records

More in Hobart

All Hobart records →